rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (3) stand juni 2016 rev 01 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. dc/dc-converter rs1-s20 2.0w unregulated single output we energize electronics! an acal group company we energize electronics! ? 4 pin sil package ? 1000vdc isolaton ? up to 3000vdc isolaton ? low ripple and noise ? efciency up to 88% ? operatng temperature range: -40 ~ +85c ? non conductve black plastc case ? emi complies with en55022 class b output specification voltage accuracy: 3% line regulaton: 1.2% (per 1%vin change) load regulation: 10% ( from 20 to 100%) load output 3.3v model: 20% ripple noise (20mhz bandwidth): 150mv pk-pk temperature coefcient: 0.02% c capacitor load: see table input specifications voltage range: 10% max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 20ma pk-pk general specifications efciency: see table i/o isolaton voltage (60sec): 1000 ~ 3000vdc i/o isolaton capacitance: 60pf typ. i/o isolaton resistance: 1000m ohm switching frequency: variable 70khz humidity: 95% rel h reliability calculated mtbf : >1.121mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: non-conductve black plastc (ul94v-0 rated) nickel-coated copper pin material sip case: ? 0.5mm alloy42 solder-coated potng material: epoxy (ul94v-0 rated) weight case- sip: 1.8g dimmension sip: 0.46 x 0.29 x 0.40 absolute maximum ratings (1) input surge voltage (100ms)/ 5 v models: 7vdc max 12v models: 15vdc max 15v models: 18vdc max 24v models: 28vdc max 48v models: 54vdc max soldering temperature (2) : 260c max. emc specifications radiated-/conducted emissions: en55022 class b esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a rohs
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (3) stand juni 2016 rev 01 rd1 - xx xx x xx power (w) input 03=3.3v t ype a x code inter nal isolation (kvdc) 48=48v 20= 2.0 48=48v model selection guide model number input input current output output current dc/dc-converter - nrete ne tt we energize electronics! an acal group company we energize electronics! u s o
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (3) stand juni 2016 rev 01 emi filter input filter components (c1, l , c2 , c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. c1 l c2 c 3 rs1 - 05xx s20 ax 1210, 2.2uf/100v 1 8 u h rs1 - 12xx s20 ax 1210, 2.2uf/100v 1 8 u h rs1 - 15xx s20 ax 1210, 2.2uf/100v 18uh rs1 - 24xx s20 ax 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv rs1 - 48xx s20 ax electrolytic capacitor, 1 0 uf/100 v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv 1. ripple/noise measured with 20mhz bandwidth. 2. tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. 6. input filter components are be required to help meet conducted emission class b, which application refer to the emi filter of design & feature configuration. 7. an external filter capacitor is required if the module has to meet iec61000 - 4 - 4. the filter capacitor rsg suggest: nippon - chemi - con ky series, 470uf/100v. +vout +v in dc/dc converter - vin - vout c3 l load c 1 c 2 emi filter input filter components (c1, l , c2 , c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. c1 l c2 c 3 rs1 - 05xx s20 ax 1210, 2.2uf/100v 1 8 u h rs1 - 12xx s20 ax 1210, 2.2uf/100v 1 8 u h rs1 - 15xx s20 ax 1210, 2.2uf/100v 18uh rs1 - 24xx s20 ax 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv rs1 - 48xx s20 ax electrolytic capacitor, 1 0 uf/100 v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv 1. ripple/noise measured with 20mhz bandwidth. 2. tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. 6. input filter components are be required to help meet conducted emission class b, which application refer to the emi filter of design & feature configuration. 7. an external filter capacitor is required if the module has to meet iec61000 - 4 - 4. the filter capacitor rsg suggest: nippon - chemi - con ky series, 470uf/100v. +vout +v in dc/dc converter - vin - vout c3 l load c 1 c 2 emi filter input filter components (c1, l , c2 , c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. c1 l c2 c 3 rs1 - 05xx s20 ax 1210, 2.2uf/100v 1 8 u h rs1 - 12xx s20 ax 1210, 2.2uf/100v 1 8 u h rs1 - 15xx s20 ax 1210, 2.2uf/100v 18uh rs1 - 24xx s20 ax 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv rs1 - 48xx s20 ax electrolytic capacitor, 1 0 uf/100 v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv 1. ripple/oie eaure it 20h ait. 2. ete y iial vi a cotat reitie loa. 3. eaure put relecte ripple curret it a iulate ource iuctace o 12uh. 4. eceei te aolute rati o te uit coul caue aae. t i ot alloe or cotiuou operati. 5. peratio uer o - loa coitio ill ot aae tee eice, oeer tey ay ot eet all lite peciicatio. 6. put ilter copoet are e reuire to elp eet coucte eiio cla , ic applicatio reer to te e filter o ei eature coiuratio. 7. a eteral ilter capacitor i reuire i te oule a to eet ec61000 - 4 - 4. e ilter capacitor rs uet ippo - cei - co k erie, 470uf/100v. vout v i c/c coerter - vi - vout c3 l loa c 1 c 2 dc/dc-converter rs1-s20 2.0w unregulated single output we energize electronics! an acal group company we energize electronics! rs1-xxxxs20a1 rs1-xxxxs20a1 (the pin connecton of high isolaton one is the same with normal one). the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
